Auxuro

Codes and materials

Materials and fabrication

Brackets, frames and plant supports are where mechanical work meets structural steel. Steel and stainless grades, sections and sheet, coatings, bolts and screws, welding, flanges and gaskets, tanks and pressure vessels, and the strength of materials behind all of it.

8.8Bolt property class: 800 MPa tensile strength, 640 MPa yield
316Stainless with 2–3% molybdenum for coastal, chemical and wastewater work
7.85 t/m³Density of carbon steel for weight estimates

Steel and stainless steel

Carbon and alloy steel

  • Low-carbon (mild) steel, about 0.05–0.25% carbon, bends cold and welds easily; more carbon makes steel harder and more brittle.
  • Mild steel yield is about 250 MPa for design estimates.
  • Alloy steels such as 4140 and 4340 are heat-treated for shafts and high-strength parts.
  • Hot-rolled sections and bars versus cold-rolled sheet and precision sections; cold-rolled has a better finish, tighter sizes and slightly higher yield.

Stainless grades

  • 304 (18/8): about 18% chromium and 8% nickel; the general and food-grade choice. 304L is low carbon for welding.
  • 316 and 316L add 2–3% molybdenum for better resistance to chloride pitting.
  • Duplex 2205: about twice the yield of 316 (at least 450 MPa) and a pitting resistance number of about 35, against 24–26 for 316L.
  • Ferritic (430) and martensitic (410) grades are magnetic; 17-4PH is precipitation hardened.
  • Pickle and passivate after welding to remove heat tint and restore corrosion resistance.

Sections and sheet

  • PFC parallel flange channel, TFB taper flange beam, WB and WC welded beams and columns, EA equal angle, RHS and SHS hollow sections.
  • Galvanised coil for ductwork; zinc-iron alloy coated sheet for welding and painting; pre-painted steel for roofs and cladding (often 0.55 mm base metal thickness).
  • Aluminium composite panel: two aluminium skins on a core; check the core’s fire rating.

Coatings

Galvanising

  • Hot-dip galvanising coats inside and out; plug or re-tap threaded holes after dipping.
  • Use galvanised bolts, nuts and washers with galvanised steel, and repair damage with zinc-rich paint.

Paint and powder coat

  • Powder coat is sprayed electrostatically and cured at about 180–200 °C, typically 60–80 µm thick.
  • Phosphate pre-treatment and primer before paint; anodising for aluminium.
  • Specify colours to AS 2700 or the paint maker’s colour code.

Choosing by cost and exposure

  • Cost: painted carbon steel < galvanised < stainless steel.
  • Coastal and roof-top plant: galvanised plus paint, or 316 stainless.
  • Corrosive process air: polypropylene, PVC or GRP rather than metal.

Bolts and screws

Property classTensile strengthYield strengthTypical use
4.6400 MPa240 MPaCommercial bolts, light brackets
4.8400 MPa320 MPaGeneral fasteners
8.8800 MPa640 MPaStructural connections, plant supports
10.91000 MPa900 MPaHigh-strength joints
12.91200 MPa1080 MPaMachine parts

Reading the class (ISO 898-1): the first number × 100 is the tensile strength in MPa; the two numbers multiplied × 10 is the yield. Design with proof or yield stress, never tensile strength. Tightening torque T = K × F × d (torque coefficient × preload × nominal diameter).

Welding, flanges and gaskets

Welding

  • Fillet welds for lapped and tee joints, butt welds for in-line joints; stitch (intermittent) or seam (continuous).
  • TIG and plasma welding for stainless tanks; MIG and stick for structural steel.
  • Simplest weld check: load ÷ weld throat area against the allowable stress of the weld metal.
  • Structural steel welding: AS/NZS 1554.

Flanges

  • Australia and New Zealand commonly use AS 2129 Table D and Table E; DIN and ANSI flanges come with imported equipment.
  • Slip-on and threaded flanges for low pressure, weld-neck for higher pressure.
  • PCD is the pitch circle diameter of the bolt holes; DN is the nominal bore.

Gaskets

  • Non-asbestos compressed fibre for general water and air.
  • NBR (nitrile) for oils; EPDM for water and weather but not fuel; Viton for heat and chemicals; PTFE where corrosion resistance matters most.
  • Spiral-wound gaskets for high pressure and temperature.

Tanks and pressure vessels

Standards

  • Pressure vessels: AS 1210, with design, fabrication and hydrostatic testing above the design pressure.
  • Steel tanks for flammable and combustible liquids: AS 1940 for storage and AS 1692 for the tanks; minimum shell thickness depends on the tank type and diameter.
  • Pressure vessels are usually checked with the maximum shear stress (Tresca) theory, which is conservative.

Good practice

  • Gauge pressure is measured above atmospheric; absolute pressure adds the atmosphere.
  • Double-wall fuel tanks need interstitial monitoring, bunding where required, and fire protection close to buildings.
  • Tube is precision drawn for compression and flare fittings; pipe is for welded and threaded joints.

Strength of materials

Basics

  • Stress = force ÷ area; strain = change in length ÷ length; in the elastic range stress ÷ strain is the elastic modulus.
  • Where there is no clear yield point, yield is defined at 0.2% permanent set.
  • Ductile materials stretch more than 5% before breaking; brittle ones do not.
  • Fatigue cracks usually start at the surface, so surface finish matters.

Design checks

  • Allowable stress = yield ÷ safety factor for ductile materials (factor about 1.1–2); brittle materials use tensile strength ÷ about 6.
  • Large welded frames such as lifting frames typically use a factor of 1.6–1.8.
  • Von Mises stress (as reported by FEA) for ductile metals; maximum principal stress for cast iron and concrete.
  • Sheet metal bend allowance uses the K factor to find the flat length.

Related guides and tools

Sources

Checked October 2026. Standards and rules change; confirm the current edition before you rely on them.

  1. ISO 898-1 Mechanical properties of fasteners – bolts, screws and studs
  2. AS/NZS 1554 Structural steel welding
  3. AS 1210 Pressure vessels; AS 1692 Steel tanks for flammable and combustible liquids; AS 1940
  4. AS 2129 Flanges for pipes, valves and fittings
  5. Australian Stainless Steel Development Association: grade data